- #Ethernet network mac address serial number#
- #Ethernet network mac address manual#
- #Ethernet network mac address code#
- #Ethernet network mac address Pc#
- #Ethernet network mac address windows#
What is the serial number portion of the MAC address for this device? What is the OUI portion of the MAC address for this device? : Saturday, Septem11:08:36 AMĭefault Gateway. : Intel(R) 8257 7 LM Gigabit Network Connection
#Ethernet network mac address code#
This 3-byte code is assigned to the vendor by the IEEE organization. These first six hex digits (3 bytes) are also known as the organizationally unique identifier (OUI). Reading the MAC address from left to right, the first six hex digits refer to the vendor (manufacturer) of this device. When using the ipconfig /all command, notice that MAC addresses are referred to as physical addresses. You can issue the ipconfig /all command to view the MAC address of your NIC.
#Ethernet network mac address Pc#
Step 1: Analyze the MAC address for the PC-A NIC.īefore you analyze the MAC address on PC-A, look at an example from a different PC NIC. You will issue commands to display the MAC addresses on a PC and a switch, and analyze the properties of each one. Note : MAC addresses are also called physical addresses, hardware addresses, or Ethernet hardware addresses. The following example shows the same MAC address using the three different notation methods:Ġ0-05- 9A-3C-78-00 00:05:9A:3 C:78:00 0005.9A3C.7800 They are displayed using six sets of hexadecimal digits that are usually separated by dashes, colons, or periods. Part 2: Display, Describe, and Analyze Ethernet MAC AddressesĮvery device on an Ethernet LAN has a MAC address that is assigned by the manufacturer and stored in the firmware of the NIC.
#Ethernet network mac address windows#
* Mar 1 00:07:59.048: %SYS-5-CONFIG_I: Configured from console by consoleĬlose a configuration window Step 4: Verify network connectivity.Ĭlose a Windows command prompt. Configure and enable the SVI interface for VLAN 1.Assign a hostname to the switch based on the Addressing Table.Console into the switch and enter global configuration mode.Įnter configuration commands, one per line.In this step, you will configure the device name and the IP address, and disable DNS lookup on the switch. The switch has not been configured yet.Ĭlose a Windows command prompt Step 3: Configure basic settings for the switch. From the command prompt on PC-A, ping the switch address.Configure the IPv4 address, subnet mask, and default gateway address for PC-A.Step 2: Configure the IPv4 address for the PC. Power on all the devices in the topology.Attach the devices shown in the topology and cable as necessary.Step 1: Cable the network as shown in the topology. For device name and address information, refer to the Topology and Addressing Table. In this part, you will set up the network topology and configure basic settings, such as the interface IP addresses and device name. Instructions Part 1: Configure Devices and Verify Connectivity Ethernet cables as shown in the topology.Console cable to configure the Cisco switch via the console ports.1 PC (Windows with a terminal emulation program, such as Tera Term).1 Switch (Cisco 2960 with Cisco IOS Release 15.2(2) lanbasek9 image or comparable).
#Ethernet network mac address manual#
If you are unsure, ask your Answers.Īnswers N ote : Refer to the Answers Lab Manual for the procedures to initialize and reload devices. Note : Make sure that the switches have been erased and have no startup configurations. Depending on the model and Cisco IOS version, the commands available and the output produced might vary from what is shown in th e labs. Other switches and Cisco IOS versions can be used. Note : The switches used are Cisco Catalyst 2960s with Cisco IOS Release 1 5. You will verify your configurations by testing for network connectivity.Īfter the devices have been configured and network connectivity has been verified, you will use various commands to retrieve information from the devices to answer questions about your network equipment. You will configure the switch and PC to match the addressing table. You will cable the equipment as shown in the topology. This lab will explore and analyze the components that make up a MAC address, and how you can find this information on a switch and a PC. This address is assigned by the man u facturer and stored in the firmware of the NIC. Part 2: Display, Describe, and Analyze Ethernet MAC Addresses Background / ScenarioĮvery device on an Ethernet LAN is identified by a Layer 2 MAC address. Part 1: Configure Devices and Verify Connectivity